£6.99
Includes M6 Hex head bolts for the flat mount wings (standard interface).
Please tell us which wing set you ride at the time of ordering
The FLITE Wing Bolt Sets include M6 Hex head bolts for the flat mount wings (standard interface).
Please tell us which front wing you ride at the time of ordering so we provide the correct bolts.
We hold stock of all sizes and orders are usually dispatched on same day (Mon-Fri).
Material: Marine Stainless Steel
We currently only deliver to the UK. Please contact us for international sales and delivery options.
We aim to send your order within 1-2 working days of it being placed (subject to payment authorisation and stock availability). All quoted delivery times are based on standard working days (Mon-Fri) and excludes public holidays.
Orders under £100 – £4.99 (Standard UK delivery*)
Orders over £100 – FREE
*Prices will vary for delivery to UK islands and Northern Ireland.
See our Delivery Terms for more information.
These instructions will walk you through the replacement of the two Lip seals and perform your own oil change.
Note: It will be easier to perform these repairs with the mast removed.
Step 1
If the Lift LCS is installed, remove the prop. For a conventional prop, remove the center bolt, then pull out the propeller and pin (the pin may fall out, make sure not to lose it). If the propeller is jammed, you may try to: a. lightly tap on it, b. soak it in water for about an hour, or, c. use a prop remover.
Remove the four screws that connect the LCS base or shroud to the motor casing. Slide out the LCS base or shroud. Four replacement screws are provided. Use NEW/provided Allen Wrenches to remove the screws.
Step 3
Remove the Rotary Seal from the shroud or LCS base. Use a sharp object is required. Replace with provided Lip Seal, open side facing motor.
Step 4
Use a sharp object to remove Lip Seal from motor. Remove and replace the compression O-Ring.
Step 5
Remove the drain fill screw and replace the O Ring. Tilt the motor with the screw hole facing downward. Without the seal and screw, the oil should drain easily; While the drain hole faces down, twist and rotate the motor housing in a circular motion to help the oil accumulate at the opening. If the oil appears very milky, clean it using brake cleaner. Use the straw attachment on the brake cleaner can to spray up the drain hole and help flush out any contaminants.
FAILURE TO COMPLY WITH THESE WARNINGS MAY RESULT IN SERIOUS INJURIES.
KONRAD Wingman V4 - 5 metre wing
MANERA Poncho
MANERA Car Seat Cover
MANERA Tee
MANERA Cap
Competition Terms
| ONEWHEEL Pint | ONEWHEEL Pint X | ONEWHEEL GT | |
| Top Speed: | 26kmh / 16mph | 29kmh / 18mph | 32kph / 20mph |
| Range: | 6-8 miles | 12-18 miles | 20-32 miles |
| Charge Time: | 80-120 minutes | 110-225 minutes | 200 minutes (90 min with GT Hypercharger) |
| Battery: | NMC Lithium-ion | NMC Lithium-ion | NMC Lithium-ion |
| Weight: | 10.5kg | 12.2kg | 15.8kg |
| App: | Provides live speed, battery life, mileage, ride style, community features and diagnostics | ||
| Brakes: | Regenerative Braking | Regenerative Braking | Regenerative Braking |
| Motor: | 750W Hypercore Hub Motor | 750W Hypercore Hub Motor | 750W Hypercore Hub Brushless Motor |
| Tyre: | 10.5in x 6.5-6in Vega | 10.5in x 4.5-6in Onewheel | 11.5in x 6.5-6.5in Onewheel |
| Remote Control: | No Remote – Lean and go | No Remote – Lean and go | No Remote – Lean and go |
| Lighting: | LED strip for battery status and in-ride alerts | LED strip for battery status and in-ride alerts | Intelligent LED Lights – White Front and Red Rear |
| Sensors: | Solid state MEMS 6-DOF | Solid state MEMS 6-DOF | Solid State MEMS 6-DOF |
| Size: | 8.75 x 10.5 x 27 inches | 8.75 x 10.5 x 27 inches (222 x 266 x 689 mm) | 9.5 x 11.5 x 29 inches (241 x 292 x 737 mm) |
Please send us your lesson request and we’ll reply to you as soon as possible.
Below is a rough guide to help determine Hover Wing Foil board size based on rider weight and skill level. A “beginner” rider is considered as someone with no previous board sport experience.
Keep in mind that additional factors, such as wind conditions, foil, and kite wing size will play an important role in the selection of the right board size.
As a rule of thumb, we recommend erring on the side of a more buoyant board with a volume that matches rider weight (for example, an 80kg rider will need at least an 80L board or larger). Riding a “sinker” will work in locations with steady, strong winds, while floatier boards prove to be a safer choice as they allow the rider to get back to shore even if the wind drops under a foilable limit.
40 L:
Not recommended for beginners or intermediate
Up to 70 kg for advanced/highly skilled riders
50 L:
Not recommended for beginners or intermediate riders
Up 75 kg for advanced/highly skilled riders
60 L:
Not recommended for beginners
Intermediate riders up to 45 kg
Advanced and highly skilled riders up to 85 kg
75 L:
Not recommended for beginners
Intermediate riders up to 55 kg
Advanced riders up to 90 kg
85 L:
For beginners up to 50 kg
Intermediate riders up to 70 kg
Advanced riders up to 100 kg
95 L:
For beginners up to 60 kg
Intermediate riders up to 80 kg
Advanced riders up to 105 kg
110 L:
For beginners up to 80 kg
Intermediate riders up to 95 kg
Advanced riders up to 115 kg
125 L:
For beginners up to 95 kg
Intermediate riders up to 105 kg
Advanced riders up to 130 kg
140 L:
For beginners up to 115 kg
Intermediate riders up to 125 kg
Advanced riders up to 160 kg
